Free calculator

Rebar Calculator: How Much Rebar Do I Need?

Bar counts, total linear feet, and weight in pounds and tons for slab grids and footings - #3 through #11 bars with a lap allowance for splices. No sign-up; the math runs entirely in your browser.

By Basharat Ali, FounderCalculation reviewedUpdated October 2026

feet

feet

inches on center

weight per foot

% for overlaps

You need

392.8 lb of rebar

#4 bars

28

Total length

588 ft

Weight

0.2 tons

Steps: bars each way = floor(span ÷ spacing) + 1, total length × (1 + 5% lap) = 588 ft × 0.668 lb/ft (#4).

Planning estimate. Rebar size and spacing for structural work should follow your local building code or an engineer's spec - #4 at 18 in on center is common for residential slabs, not a rule.

Estimated cost

What will it cost?

Enter your local store prices — prices vary by region.

  • Rebar #4 (20-ft sticks)

    30 sticks

    —

Estimate — prices vary by store and region. Check your local store for current pricing.

Worked example: 20×20 ft slab

Full arithmetic, step by step (#4 bars at 18 in on center, 5% lap):

  1. Bars each way: floor(240 ÷ 18) + 1 = 14 bars (both directions = 28 bars)
  2. Raw length: 14 × 20 + 14 × 20 = 560 ft
  3. With 5% lap: 560 × 1.05 = 588 ft
  4. Weight: 588 × 0.668 = 392.8 lb (≈ 0.20 tons)
  5. Sticks: 588 ÷ 20 = 29.4 → 30 sticks of 20-ft #4

The formulas

Slab grid

Bars per direction = ⌊ span in inches ÷ spacing ⌋ + 1 - then total feet = (bars₁ × length) + (bars₂ × width), times (1 + lap).

Weight

Pounds = total feet × lb/ft for the bar size - using published weights (#4 = 0.668 lb/ft). Tons = pounds ÷ 2,000.

Footing

Total feet = trench length × bars per footing - then the same lap and weight math as the slab.

Frequently asked questions

What size rebar do I need for a concrete slab?

#4 (1/2-inch) rebar at 18 inches on center is the common residential default for 4-inch slabs. Lighter duty work sometimes uses #3; heavier loads call for #5 or tighter spacing. Rebar sizing is structural - follow your local building code or an engineer's spec, not a rule of thumb alone.

How much does rebar weigh per foot?

Published weights: #3 = 0.376 lb/ft, #4 = 0.668 lb/ft, #5 = 1.043 lb/ft, #6 = 1.502 lb/ft, #7 = 2.044 lb/ft, #8 = 2.670 lb/ft. This calculator multiplies your total linear feet by the selected bar's weight and converts to tons (÷ 2,000).

How far apart should rebar be spaced in a slab?

12 to 18 inches on center covers most residential slabs; 18 inches is the common default for #4 bars in a 4-inch slab. Footings typically run 2 to 4 continuous bars rather than a grid. Wider spacing saves steel but reduces crack control - when in doubt, check the code.

How many 20-foot sticks of rebar do I need?

Divide the calculator's total linear feet by 20 and round up. For the worked example below: 588 ft ÷ 20 = 29.4, so order 30 sticks of #4. The lap allowance is already baked into the total, so don't add waste twice.

Do I need rebar in a small concrete slab?

Not always. Small non-structural slabs (shed pads, walkways) often do fine with welded wire mesh or fiber-reinforced mix instead of rebar. Rebar matters most where the slab carries real loads or spans soft spots. Check local code - some jurisdictions require it regardless of size.

What is the lap allowance for?

Rebar comes in fixed lengths (usually 20 ft), so long runs need overlapping splices. The lap allowance adds a percentage to the total length to cover those overlaps - 5% is a reasonable planning figure. Lapped splices also have minimum length requirements by bar size in the code.

Keep estimating

Related calculators