Cost guide

How Much Does a New Roof Cost?

Roofers quote by the square (100 sq ft of roof surface), and your roof is bigger than your house footprint once pitch is counted. Here are the typical ranges for shingles and metal, plus what pushes any quote up or down.

By Basharat Ali, FounderCalculation reviewedUpdated October 2026

Ranges, not quotes. All figures below are typical US ranges reported by contractors and home-improvement sources. Actual prices vary widely by region, pitch, layers to remove, and roof complexity, use them to evaluate quotes, not replace them.

Quick answer: typical roofing cost ranges

Roofing materialTypical range (per square, installed)
3-tab asphalt shingles$350-$550
Architectural asphalt shingles$450-$750
Standing-seam metal$800-$1,400
Tear-off and disposal (one layer)$100-$200 extra per square

A 1,500 sq ft roof footprint is roughly 16-17 squares once pitch and waste are counted, so architectural shingles run roughly $7,200-$12,750 installed before tear-off and decking repairs. Metal roughly doubles that figure but lasts decades longer.

What drives the price

  • Pitch. The steepest lever. A steep roof needs safety gear, slower work, and more staging, and labor climbs fast past a walkable pitch. Use our roof pitch calculator to find yours before getting quotes.
  • Roof size in squares. Pitch inflates the footprint: a 6-in-12 pitch adds about 12% over the footprint area, a 12-in-12 pitch adds about 41%. Quotes should state squares, not footprint square feet.
  • Tear-off layers. One layer is standard; two layers cost more to remove and haul, and the landfill fees scale with weight.
  • Decking repair. Rotten or soft sheathing found during tear-off is replaced by the sheet, usually billed per sheet on top of the quote. Old roofs often hide some.
  • Flashing, vents, and penetrations. Chimneys, skylights, valleys, and vents each need flashing work, and each one is a potential leak if done cheaply.
  • Underlayment and ice barrier. Synthetic underlayment is standard now; ice-and-water shield along eaves and valleys is cheap insurance in cold climates.

Worked example: 1,500 sq ft roof, architectural shingles

  1. Roof surface: 1,500 sq ft footprint at a moderate pitch plus waste works out to roughly 16 squares. Run your footprint and pitch through our roof shingles calculator for bundles and squares.
  2. Shingles installed: 16 x $450-$750 = $7,200-$12,000.
  3. Tear-off (one layer): 16 x $100-$200 = $1,600-$3,200 more.
  4. Typical total: roughly $8,800-$15,200, before decking repairs, flashing upgrades, or permits.

DIY vs. hiring a contractor

Roofing is the job most worth hiring out. Falls are the leading cause of construction deaths, steep work needs harnesses and staging, and manufacturer warranties often require certified installation. A DIY roof also risks the two most expensive mistakes in the trade: bad valley flashing and bad penetrations, both of which leak slowly and rot the decking. Get three quotes, check that each lists squares, tear-off, underlayment, flashing, and cleanup, and compare those line items rather than the bottom lines.

Frequently asked questions

How much does a new roof cost for a 1,500 sq ft house?

A 1,500 sq ft roof footprint is roughly 16-17 squares once pitch and waste are counted. In architectural asphalt shingles at a typical $450-$750 per square installed, that runs roughly $7,200-$12,750 before tear-off and decking repairs. Steep pitch, multiple layers to remove, and skylights or chimneys push toward the higher end.

Are architectural shingles worth it over 3-tab?

For most homes, yes. Architectural (dimensional) shingles cost more per square but are thicker, look better, resist wind better, and usually carry longer warranties. 3-tab shingles are the budget option and make sense for a rental, a shed, or a roof you plan to replace soon anyway.

How much does roof tear-off cost?

As a typical range, removing one layer of old shingles and hauling it away adds about $100-$200 per square, and a second layer adds more. Some quotes bundle tear-off into the per-square price and some list it separately, so always ask which one you are looking at.

How long does an asphalt shingle roof last?

3-tab shingles typically last 15-20 years and architectural shingles 25-30 years in normal conditions, though heat, poor ventilation, and storm damage shorten both. Metal roofs last much longer (40-70 years) but cost roughly double up front.

Can a new roof go over the old shingles?

Building codes in many areas allow one overlay layer, and it saves the tear-off cost. But it hides decking damage, adds weight, and shortens the new roof's life, and most roofers recommend a full tear-off for a roof you plan to keep long term. Get the decking inspected either way.

Ready to size the job? Use the roof shingles calculator for bundles and squares, check your pitch with the roof pitch calculator, and see the siding cost guide if the exterior walls are due at the same time.